| T | Key | Component | Summary |
|---|
| TD-18623 | 12d Field - General | 12d Field codes opcodes: turn into choice list |
| TD-21283 | 12d Field - General | 12d Field hidden point tolerance check |
| TD-19125 | 12d Field - General | 12dF_BLUETOOTH_DEVICES.TXT, append new devices rather than overwrite. |
| TD-19938 | 12d Field - General | 12dField config file paths, check and document. |
| TD-16459 | 12d Field - General | Ability to disable battery level warning wasn't available in "12dF_Battery_Levels.4D" |
| TD-19773 | 12d Field - General | Add "Log" button to user comment panel rather than needing to hit "Finish" |
| TD-16503 | 12d Field - General | Add attributes for working directory and model |
| TD-20061 | 12d Field - General | Add check to detect whether NMEA data has been rounded to 1dp |
| TD-14607 | 12d Field - General | Add height of secondary GPS instrument to target heights panel. |
| TD-13991 | 12d Field - General | Add interface for Leica ATR visibility settings (older instruments) |
| TD-17180 | 12d Field - General | Add macro "AusGeoid_To_Points_Panel.4do to the menu |
| TD-18004 | 12d Field - General | Add new Trimble searches, turn and search to GNSS location. |
| TD-16606 | 12d Field - General | Add phase centre correction to device setup |
| TD-20175 | 12d Field - General | Add SDR Memo for changes to TPS measurement settings. |
| TD-16434 | 12d Field - General | Add setting to force all 12dField panels inside the main 12d screen. |
| TD-16935 | 12d Field - General | Add setting to not add tolerances page to setout tabs to setout panels |
| TD-14628 | 12d Field - General | Add standard deviations to the helmert setup attributes |
| TD-22245 | 12d Field - General | Add the Point id type to the setout Names panel |
| TD-20014 | 12d Field - General | Add TPS Sokkia (Generic) to instrument list. |
| TD-19301 | 12d Field - General | Added 12dF_EXCLUDED_ATTRIBUTES.4D allowing user exclusion of vertex attributes. |
| TD-19000 | 12d Field - General | Added new instrument, Topcon Generic TPS. |
| TD-21716 | 12d Field - General | Added phase centre value into "12df_GPS_PROFILES.4d" and applied on profile selection. |
| TD-16516 | 12d Field - General | Allow 12dF_AUTO_START_PANEL.4D to start multiple panels |
| TD-21742 | 12d Field - General | Allow a compact start up panel for 12dField |
| TD-15720 | 12d Field - General | Allow Leica guide lights toggle to low/medium&high |
| TD-18342 | 12d Field - General | Allow setting of TPS sim base and measured point without bringing up the panel when using standard setup |
| TD-17902 | 12d Field - General | Allow TPS combined n-value to be long/lat or east/north based. |
| TD-18709 | 12d Field - General | Allow tps or gps hotkey files, 12dF_TPS/GPS_HOTKEY_BARS.4d |
| TD-16492 | 12d Field - General | Allow user to disable remembering of last IR/RL target heights. |
| TD-16433 | 12d Field - General | Always prompt to use out of tolerance multiface reading in setout panels. |
| TD-20882 | 12d Field - General | AP20: icon for prism location indicates IMU is active when in tilt mode. |
| TD-20706 | 12d Field - General | Attributes for tps target, names, type, constant, aperture. |
| TD-17228 | 12d Field - General | Auto check for 12dF control bar position if user tries to start 12dF while already running. |
| TD-18622 | 12d Field - General | Automatically close TPS simulator settings panel on exiting 12dField |
| TD-16936 | 12d Field - General | Basic string setout, make single string default option and set control as the selected single string. |
| TD-20007 | 12d Field - General | Captivate 7 firmware, add setting of loss of lock prediction duration |
| TD-20764 | 12d Field - General | Comment panel, current date/time not updated for TPS Sim, Trimble or Topcon. |
| TD-19812 | 12d Field - General | Complete revamp of TPS joystick functionality. |
| TD-19592 | 12d Field - General | Create NMEA Replay String panel needs the current projection details |
| TD-18546 | 12d Field - General | Deprecated virtual bluetooth com ports not shown if Win10, 1903 or better |
| TD-17247 | 12d Field - General | Enable 12dF config files to be stored in a special directory 12dF_current_settings |
| TD-17144 | 12d Field - General | Enforce strict control model id's, no duplicate ids and no blank ids |
| TD-17917 | 12d Field - General | Extra hotkeys fst/std std/stk & fst/ftk toggles. |
| TD-20930 | 12d Field - General | Fail more gracefully if AP20 is not clicked in correctly for height |
| TD-21115 | 12d Field - General | For Leica TPS firmware >= V7 prediction and lock type available in 12dField |
| TD-19523 | 12d Field - General | General settings tab menus tab does not differentiate TPS/GNSS routines |
| TD-19549 | 12d Field - General | GNSS 2.5 Helmert, translate x,y values were confusing because of 0, 0 based origin |
| TD-19548 | 12d Field - General | GNSS Helmert 2.5 Panel local n-value super alignment was not implemented. |
| TD-20064 | 12d Field - General | GNSS localization, make n-value optional. |
| TD-20060 | 12d Field - General | GNSS localization, write 12da of local string/trimesh to localization file |
| TD-20339 | 12d Field - General | GNSS Vector Panel |
| TD-20046 | 12d Field - General | GPS Client should not filter NMEA messages. |
| TD-17835 | 12d Field - General | GPS, geoid, (n-value) calcs separated from the helmert localisation |
| TD-21511 | 12d Field - General | GVR: Place symbols on averaged and observed points |
| TD-18592 | 12d Field - General | Helmert Panel: improve enable/disabling of buttons. |
| TD-20358 | 12d Field - General | ID support for Leica AP20 smart pole |
| TD-20948 | 12d Field - General | Leica MPR122 availability needs to be user definable. |
| TD-17978 | 12d Field - General | Leica TPS spiral search needs the initial GPS XY/XYZ options as well. |
| TD-20008 | 12d Field - General | Leica TPS, prevent use of function keys when in prediction mode, |
| TD-19479 | 12d Field - General | Make 12dField menus camel case |
| TD-20921 | 12d Field - General | Manual tape measurements for Topcon Generic TPS |
| TD-20366 | 12d Field - General | Multiface lock modes for Leica, GUI not refreshing correctly on done. |
| TD-21080 | 12d Field - General | New type "None" for GNSS N value, uses ellipsoid height only. |
| TD-17523 | 12d Field - General | Possible to set a null target/extra target height |
| TD-16453 | 12d Field - General | Pressing STOP on panel should cancel an ATR search |
| TD-16138 | 12d Field - General | Prevent target height next hotkeys being pressed while instrument changing modes. |
| TD-16740 | 12d Field - General | Rearrange items on the 12d Field Utilities menu |
| TD-20806 | 12d Field - General | Reduce Topcon TPS options to Generic and External Link. |
| TD-20631 | 12d Field - General | Relectorless tracking working for Topcon Generic instruments. |
| TD-20004 | 12d Field - General | Removed custom user keys for each setout panel. |
| TD-21654 | 12d Field - General | Report on GVR averaged observed points to TSS Points. |
| TD-18591 | 12d Field - General | Resection panels, details tab, scales factors made more consistent |
| TD-16397 | 12d Field - General | SDR Pickup to capture and store secondary setout panel attributes |
| TD-19636 | 12d Field - General | Set Topcon default wait time default to 3599 |
| TD-19524 | 12d Field - General | Setup visualisation shouldn't be shown in GNSS settings panel |
| TD-17820 | 12d Field - General | Shutdown button only added to control bar when both ctrl&menu unticked. |
| TD-17476 | 12d Field - General | Some 12dF panels should not be allowed to have multiple copies. |
| TD-19525 | 12d Field - General | Station details, added number of readings for helmert and least squares setups. |
| TD-17542 | 12d Field - General | String reference is not being stored as attribute when smart find is on. |
| TD-18779 | 12d Field - General | Target height box: warning when extra height is set |
| TD-20092 | 12d Field - General | TDF GNSS Localisation Export Local String to Model |
| TD-19698 | 12d Field - General | Topcon Generic TPS, remove environment variable for usage |
| TD-19768 | 12d Field - General | Topcon Generic, allow RC5 Handle button press to be set to hotkeys. |
| TD-16998 | 12d Field - General | TPS simulator settings panel not available as a hotkey |
| TD-17900 | 12d Field - General | TPS, better searching ability via combined 2nd GPS inst and cube search |
| TD-20610 | 12d Field - General | Update instruments other than the Leica to new bitmaps and prompts. |
| TD-10486 | 12d Field - General | Update TPS Helmert/LSA panels |
| TD-19587 | 12d Field - General | User values panel needs to be TPS/GNSS aware. |
| TD-17810 | 12d Field - General | Values not updating while the GNSS status panel was open. |
| TD-18711 | 12d Field - General | Write helmert/least squares details to a visualisation model. |
| TD-10485 | 12d Field - General | Z difference display in Helmert and Least squares resection panels |
| TD-19312 | 12d Field - General, Base | Allow 12dField to use new Bluetooth connection when maintenance has expired. |
| TD-17906 | 12d Field - General, Survey | Allow choice for least squares orientation by averaging or longest leg. |
| TD-16774 | 12d Field - Pickup | Add hotkey for delete last string opcode |
| TD-18428 | 12d Field - Pickup | Add the one touch MR/MS setting into SDR Settings panel |
| TD-18340 | 12d Field - Pickup | Allow auto-save of project when SDR function is created. |
| TD-16460 | 12d Field - Pickup | Allow SDR pickup to store all setout panel attributes |
| TD-21059 | 12d Field - Pickup | Enhance 12dfield_sdr_config to populate "Function" and "Field file" boxes. |
| TD-19541 | 12d Field - Pickup | GNSS measurements were not being stored as specific GNSS coordinates. |
| TD-21366 | 12d Field - Pickup | Hide the "Comment" field in the 12dF SDR Feature Code panel by default |
| TD-18337 | 12d Field - Pickup | Make the "Fast recalc" button more prominent on the SDR Pickup panel. |
| TD-18341 | 12d Field - Pickup | Move the foresight panel selection into the SDR panel |
| TD-11463 | 12d Field - Pickup | Multicode should prompt for Attributes |
| TD-20048 | 12d Field - Pickup | Point setout, "Angle is valid" overwriting message box |
| TD-18582 | 12d Field - Pickup | Recalc now called when storing check shot. |
| TD-20052 | 12d Field - Pickup | SDR Pickup feature code panel, allow Inc/Next keys to set a user default id when blank |
| TD-21040 | 12d Field - Pickup | SDR Pickup panel, updated the RHS bitmaps. |
| TD-16668 | 12d Field - Pickup | SDR Pickup, camera12d.exe needs a little bit of work. |
| TD-18338 | 12d Field - Pickup | SDR Pickup, pop up a please be patient dialog if writing the .12dField xml file. |
| TD-19241 | 12d Field - Pickup | Store some extra vertex attributes from the SDR function |
| TD-18336 | 12d Field - Pickup, Survey | SDR: disable "use coordinate commands (Opcode 2)" if control model enabled. |
| TD-14044 | 12d Field - Setout | 12dF attribute so_shift_z was not available on the nav page |
| TD-17367 | 12d Field - Setout | Add hotkeys for set value TPS rotate left/right/up/down |
| TD-17205 | 12d Field - Setout | Added a Basic Segment Setout panel |
| TD-18888 | 12d Field - Setout | Added hotkeys for TPS auto turn settings. |
| TD-18109 | 12d Field - Setout | Added toggle for current tin/trimesh face highlighting. |
| TD-19994 | 12d Field - Setout | All setout panel attributes should be stored with the primary panel. |
| TD-18559 | 12d Field - Setout | Allow 20 user definable text lines in nav and info pages. |
| TD-19481 | 12d Field - Setout | Basic segment setout missing hotkeys for NEXT, PREV & CURR |
| TD-19995 | 12d Field - Setout | Basic segment setout should have the choice of string or segment chainage. |
| TD-20051 | 12d Field - Setout | Bogus error message on clearing setout strings |
| TD-20510 | 12d Field - Setout | Change the auto clear chainage, offset & height options to allow leave, clear or zero the value. |
| TD-20677 | 12d Field - Setout | Further settings for size and colour of pole and setout/pickup points on plan view. |
| TD-18455 | 12d Field - Setout | Grid setout: non intersecting lines allowed |
| TD-21026 | 12d Field - Setout | Improve error messages for corrupted 12dField setout backup FLD files. |
| TD-20465 | 12d Field - Setout | Iterate positioning with 3D chainages improvements |
| TD-16812 | 12d Field - Setout | Iterate to distance normal from tin/trimesh |
| TD-20942 | 12d Field - Setout | Missing attribute to indicate offset point was used, added so_offset_point_base_used |
| TD-17512 | 12d Field - Setout | Multiple minor tidy ups for point setout panel. |
| TD-17540 | 12d Field - Setout | Not clearing all previous measured values prior to a new measurement, WIP. |
| TD-21110 | 12d Field - Setout | Point Setout added extra attribute for actual direction of offset point |
| TD-20195 | 12d Field - Setout | Point setout panels, missing attributes for offset distance and direction |
| TD-21041 | 12d Field - Setout | Point setout, add Clear button to zero offsets. |
| TD-17530 | 12d Field - Setout | Point setout, allow use of a trimesh vertex. |
| TD-20050 | 12d Field - Setout | Point setout, make offsetting a point more usable on a tablet. |
| TD-20053 | 12d Field - Setout | Point store setup was losing linestyle settings. |
| TD-17556 | 12d Field - Setout | Rename stake height diff and shift value attributes |
| TD-16789 | 12d Field - Setout | Rename string setout panels to 'Basic' and 'Advanced'. |
| TD-16776 | 12d Field - Setout | Rename Tin Setout Panel to 'Surface' and tweak, |
| TD-19600 | 12d Field - Setout | Replace the "TAB->" button with "Setup" |
| TD-17535 | 12d Field - Setout | Secondary control string was always returning extended drop. |
| TD-20134 | 12d Field - Setout | Setout point, add vertex attributes for auto find settings |
| TD-20047 | 12d Field - Setout | Split clearing of setout offset/height difference into 2 boxes. |
| TD-20049 | 12d Field - Setout | Store point setup panel was not restoring the point-line setting correctly. |
| TD-14703 | 12d Field - Setout | Store point setup, change Point/Line to tickbox |
| TD-18989 | 12d Field - Setout | Surface setout missing top/bottom Trimesh choice |
| TD-18901 | 12d Field - Setout | Surface setout, better warning for no 3d drops to supertins. |
| TD-19676 | 12d Field - Setout | Topcon generic TPS, add RC search buttons to locate prism panel. |
| TD-17359 | 12d Field - Setout | TPS Positioning selects should work from section views. |
| TD-19780 | 12d Synergy Integration | Add support for synergy path for gsb file in NValues 4d |
| TD-18848 | 12d Synergy Integration | Create Template and Function and commit |
| TD-21582 | 12d Synergy Integration | Project=>12dSynergy=>Pending - Change List to Grid |
| TD-19267 | 12d Synergy Integration | Tweaks for Synergy based Master Share Files and projects MK II |
| TD-21470 | 12d View | Markup option |
| TD-20158 | ADAC | Copy String attribute Group to Group to allow multiple attributes of the same name |
| TD-18527 | ADAC | New ADAC chain files |
| TD-20186 | Base | "Create Buildings" creates old strings. |
| TD-20017 | Base | "Create polymesh" to have "Pass other data" tick |
| TD-20796 | Base | "Create Z-Values from String to Tin Differences" panel created old 3d string |
| TD-21840 | Base | 12d start up to better handle environment variables specifying Synergy URIs |
| TD-19807 | Base | 12d Update Service ticked on as the default |
| TD-18501 | Base | 12d Usage Report (Cloud): access settings configuration file |
| TD-20162 | Base | 12da library to accept 12dxml and 12dxmlz |
| TD-21763 | Base | 12da reader: skip raster element when image file link is not found |
| TD-18268 | Base | About 12d Model: Display when project is Object Tree |
| TD-20588 | Base | Add "Computate Strings" to menu and toolbar |
| TD-20019 | Base | Add Activate and Deactivate buttons to the Create/Edit Attribute Manipulator File panel |
| TD-17043 | Base | Add all removed tins: Pre*post stem to create models |
| TD-20488 | Base | Add Comment Buttons to "Create/Edit Attribute Manipulator File" Panel |
| TD-21105 | Base | Add Copy path to the attribute grid |
| TD-21275 | Base | Add Default pixels to mm plot factor to Project Settings |
| TD-17624 | Base | Add extrude snap button to snaps lists |
| TD-20920 | Base | Add message to Wait_on_widgets for when a panel is resized |
| TD-16994 | Base | Add missing View settings to View properties, favourites etc |
| TD-20282 | Base | Add new option called Trimble LandXML Roading |
| TD-21280 | Base | Add point create to CAD Point toolbar |
| TD-21046 | Base | Add sorting by a column for attributes table |
| TD-19373 | Base | Added another tickbox to env editor for the legacy update checker |
| TD-20901 | Base | Addition of Corridor width to panel to check String to parallel & Second strings within a distance of X |
| TD-20018 | Base | Additional choice to use vertex z value when explode symbols |
| TD-16914 | Base | Additional Text Border types |
| TD-16080 | Base | Allow GDA options when maintentance module is on |
| TD-20980 | Base | Allow picking of extrusions edges and points |
| TD-20521 | Base | Allow picking of extrusions faces |
| TD-19545 | Base | Allow read of XYZ files with multiple lines of header information |
| TD-18306 | Base | Allow Text strings to be convert to string types other than Text string |
| TD-17027 | Base | Attribute editor: search button |
| TD-20738 | Base | Attribute Manipulator - Add Vertex Indices Number |
| TD-20124 | Base | Attribute manipulator, copy and paste between different panels |
| TD-19817 | Base | Attribute Manipulator: add “String start chainage” to String Properties |
| TD-17985 | Base | Attribute manipulator: Add comment type |
| TD-20545 | Base | Attribute Manipulator: Add Pt/Line type to string properties list |
| TD-20546 | Base | Attribute Manipulator: Add String type to string properties list |
| TD-19818 | Base | Attribute Manipulator: add Vertex symbol to Vertex Properties |
| TD-20423 | Base | Attribute Manipulator: Can now update existing attribute values |
| TD-19924 | Base | Attribute Manipulator: Change default Index from 1 to 0 for Segment property and Segment attribute |
| TD-19923 | Base | Attribute Manipulator: Change default Index from 1 to 0 for Vertex property and Vertex attribute |
| TD-20469 | Base | Attribute Manipulator: Insert new rule goes after the current selected rule |
| TD-17243 | Base | Attribute Manipulator: Node/Link name to and from Node/link attributes |
| TD-17052 | Base | Attribute manipulator: segment bearing and grade |
| TD-17115 | Base | Attribute Manipulator: values for internal, external, thicknesses for pipes |
| TD-22383 | Base | AttributeControlBar: mods to existing choices and add choices and |
| TD-19222 | Base | Batch migrating V14 to V15 projects |
| TD-20452 | Base | Better information in Output Window for licensing and remove misleading errors with days left on nodes file |
| TD-21851 | Base | Better progress messages during Project migration |
| TD-21278 | Base | Change dimension styles in the setups, text aligment property should use text_aligned_angle |
| TD-19935 | Base | Change icon for comment node in attribute manipulator |
| TD-19824 | Base | Change Projection box on KML writer to the new Projection Box |
| TD-21835 | Base | Choice in delete model tin panels to delete shared out data |
| TD-21893 | Base | Choice to write view favourite file number in hex float |
| TD-17809 | Base | Classify super string fills with attributes |
| TD-18684 | Base | Classify Symbols: Add symbol angle |
| TD-19849 | Base | Close text edit panel with CTRL Enter |
| TD-19806 | Base | CodeMeter Runtime ticked on as the default |
| TD-20257 | Base | Combined leader format to multiple string properties |
| TD-18190 | Base | Commas in numbers for Check Points in a project |
| TD-19454 | Base | Compile and run a drag and dropped .4dm file |
| TD-17417 | Base | Coord System box for Write Arcview - write out projection in WKT format |
| TD-19910 | Base | Copy project functions/templates missing from themes. |
| TD-17140 | Base | CPATH variable may not include USER directory when 12d starts |
| TD-20697 | Base | Create buildings for tins needs to remove vertex non tinability |
| TD-21570 | Base | Create Legends from the names.4d |
| TD-21276 | Base | Create many rasters from jpgs and jgw files |
| TD-16205 | Base | Create simple extrusions from complex extrusions |
| TD-15524 | Base | Custom menus - Ability to reset menus to default 12d without restart |
| TD-18617 | Base | Delete empty models: checking for model attributes |
| TD-21282 | Base | Delete empty text attributes |
| TD-21277 | Base | Delete Options Log Files: add "Delete older than X days" |
| TD-22198 | Base | Dongles.4d installer |
| TD-20217 | Base | Drainage_headwalls_panel Shut down on exit added |
| TD-14952 | Base | Drape mode: Drape null vertices only |
| TD-16974 | Base | Drape: Colour draped string by triangle colour |
| TD-17108 | Base | Drape: string coloured by triangle colours |
| TD-17186 | Base | Enable widget pages for Chainage Offset Filter Panel |
| TD-20589 | Base | Enhancement to the "Computate strings" macro |
| TD-17693 | Base | ENV editor too big for tablet. |
| TD-19314 | Base | Env Editor: add the AutoUpdater env variables |
| TD-14823 | Base | Env variable to remove "12d XML project data" from the menu |
| TD-16882 | Base | Filter points by chainage and offset |
| TD-20380 | Base | Find and replace text in drafting leaders and table |
| TD-21990 | Base | Force loading models containing tins at project startup |
| TD-20123 | Base | From_text_expression |
| TD-17295 | Base | GDA94 to GDA2020: don't show 7parameter unless they have the Survey module |
| TD-17748 | Base | Geo-reference rasters created by option "High Resolution OpenGL Image" using the current plan view settings |
| TD-19997 | Base | Global Height: Allow for empty Height field |
| TD-19631 | Base | Global Model Rename: add tick box “Only show matches” |
| TD-20164 | Base | Head to Tail: choices to allow non-strings to Pass |
| TD-17672 | Base | Height adjustment panel: allow super tins |
| TD-17375 | Base | Height adjustment: apply new Projection Box with GSB |
| TD-12648 | Base | Image dumps with a FOLDER of slx files |
| TD-20740 | Base | Join Many: remove individual segment colour/linestyle |
| TD-21627 | Base | Join strings options preserving segment linestyles from input strings |
| TD-21104 | Base | Keep attribute tree expansion when moving through segments and vertices |
| TD-14775 | Base | LAS Import now defaults all categorgies to true |
| TD-20163 | Base | Leader Attribute Substitution |
| TD-17538 | Base | Length 3d: include super alignments |
| TD-14939 | Base | Load super inquire styles on start-up |
| TD-20919 | Base | Log Line Group for Recent Projects List |
| TD-17682 | Base | Made topmost buttons user configurable. |
| TD-17150 | Base | Make trimeshes work with polygon choices in Source box - first step |
| TD-18051 | Base | Map File BIM Object Create Apply |
| TD-16165 | Base | Map File: Apply segment colours and segment linestyles |
| TD-16115 | Base | Map file: apply segment linestyles and segment colours |
| TD-20597 | Base | Markup option |
| TD-22178 | Base | Merging backend code of LINZ reader and WFS reader |
| TD-16585 | Base | MetaConnex Editor |
| TD-18032 | Base | Migrate pre-V15 project to V15 Guid or Object Tree project |
| TD-16396 | Base | Missing method to get tin from computator data |
| TD-21113 | Base | Model Delete: differentiate between project models and removed models |
| TD-19439 | Base | MTF menu is now a little wide when pinned up! |
| TD-19826 | Base | Neo Classic Theme |
| TD-21904 | Base | new information leader: choice to use multiple line text for when typing the format text |
| TD-19722 | Base | New item in super inquire to show (the new five) super string justification |
| TD-20160 | Base | New tick box in compile and run macro panel to retain after run |
| TD-20016 | Base | Object Tree model naming for Components |
| TD-19420 | Base | Object Tree ordering in Tree mode |
| TD-7883 | Base | Open project to allow open in a new session |
| TD-20972 | Base | Option to cut sections through strings at regular chainage interval only |
| TD-21004 | Base | Option to set all Real attributes with the value of "Input/output null height" to NULL |
| TD-19547 | Base | Options producing old strings: Tins =>Tin analysis =>Slope =>Slope analysis 2, Tins =>Tin analysis =>Slope |
| TD-17959 | Base | Options.txt and Crash logs: add field to say if current project is Object Tree or not |
| TD-17845 | Base | Panels: Highlight Active Tab on a panel |
| TD-21635 | Base | PDF reports auto open after created |
| TD-20154 | Base | Perspective Camera: show view name in message area |
| TD-20956 | Base | Picking extrusions in orbit |
| TD-20216 | Base | Pipe Controlbar: different icons for the Diameter/Culvert and the Invert/Centre/Obvert Choice boxes |
| TD-16078 | Base | Point Cloud Create Cache |
| TD-18085 | Base | Point Clouds: Drawing speed ups |
| TD-21578 | Base | Project Details Panel - Make resizable, and auto-resize lists |
| TD-21568 | Base | Project Launcher > Settings > Default Project Location folder for new and existing projects |
| TD-19118 | Base | Project Launcher: add the 12d Macro manual pdf to the icons at the bottom right |
| TD-19119 | Base | Project Launcher: Recent Projects: add a Refresh option |
| TD-21734 | Base | Projection File Editor: Correctly Save the Order of Projections and Projection Groups |
| TD-18049 | Base | Projection xml editor: Inclusion Filter for Set_ups |
| TD-17121 | Base | Projection XML editor: new editor panel |
| TD-20468 | Base | Ramp function add crease and optional tin |
| TD-19653 | Base | Relative sharing for master share |
| TD-19688 | Base | Remove module requirements from Service chamber many |
| TD-19588 | Base | Remove unused edge names from trimesh |
| TD-19399 | Base | Rename Registry file to Configuration file |
| TD-20891 | Base | Re-orient all faces coherently |
| TD-19242 | Base | Report the object name when restore fails due to mising file |
| TD-17155 | Base | Rotated Grid Panel to output super strings |
| TD-20470 | Base | Search and replace attribute values |
| TD-13216 | Base | Source box for multi Trimesh Boolean Union |
| TD-21360 | Base | Spell check while typing in text edit box |
| TD-21667 | Base | Street view: ddx support |
| TD-20153 | Base | Street view: Show position |
| TD-19232 | Base | Super inquire item type of Segment grade 1 in |
| TD-18121 | Base | Super Inquire: Add more Plot Frame properties (ie Scale, Origin, Rotation) |
| TD-21616 | Base | Super Inquire: Choice to display longer texts in multiple lines |
| TD-21615 | Base | Super inquire: new settings to display without grid |
| TD-16978 | Base | Super string: add round or culvert, thickness and Internal size tick to Create >Pipe |
| TD-18812 | Base | Super string: hard code Close and Open super string |
| TD-18808 | Base | Support Nearmap Google Earth |
| TD-20876 | Base | Test projects: make them Neo |
| TD-20522 | Base | Text Spell Checker |
| TD-19453 | Base | Tin Add to Model: remove tin from existing models |
| TD-15193 | Base | Tin Aspect analysis: add auto filling model box |
| TD-19480 | Base | Tin colour on Tin Edit menu |
| TD-21112 | Base | Tin Delete: differentiate between project tins and removed tins |
| TD-21842 | Base | Tin Information Table |
| TD-19577 | Base | Tin to strings: flag for "Don't include null triangles" |
| TD-15055 | Base | Tins: Add a copy tin to the Slope Analysis option |
| TD-15054 | Base | Tins: Add a copy tin to the tin Aspect Analysis option |
| TD-17599 | Base | Tins: Create break segments |
| TD-17622 | Base | Tins: Create naked points and triangles in the tin |
| TD-21651 | Base | Turn Automatic Update checker on |
| TD-20563 | Base | Turn off heads up display by default |
| TD-18528 | Base | Update files for HTML section plot |
| TD-21054 | Base | Updated Function Attributes Editor |
| TD-21053 | Base | Updated Model Attributes Editor |
| TD-20935 | Base | Updated panel to send tin raster to back of views |
| TD-21052 | Base | Updated Project Attributes Editor |
| TD-21061 | Base | Updated Tin Attributes Editor |
| TD-21567 | Base | URL-Hyperlink Access through 12d Model and 12d View Attribute Lists |
| TD-22290 | Base | Use double click to highlight the SA for resolve SA chain command |
| TD-17340 | Base | Version numbers for 12da/12dXML |
| TD-20125 | Base | View =>New view menu: put "Perspective OpenGL" above "Perspective" |
| TD-20552 | Base | View Toggles: Behaviour when Draw Solid and Draw Edges are both off |
| TD-20281 | Base | XYZ Ch/HT Message to use separators for large coordinates |
| TD-17717 | CAD | "Snaps Cad" choice to select a segment |
| TD-18016 | CAD | 12d acad paste: add model prefix |
| TD-18030 | CAD | 1-point tin slope and direction label |
| TD-17729 | CAD | Add the key "o" in move segment for offset |
| TD-19092 | CAD | Better finish message for CAD paste pre postfix panel |
| TD-14439 | CAD | CAD Leader: add the tin properties crossfall, slope, grade, colour, name, aspect etc |
| TD-16595 | CAD | Cad text suggested alignment |
| TD-16504 | CAD | Drafting Elements: Allow Utilities - H-Z - Translate to operate on them |
| TD-18935 | CAD | Extend 3d vertex to a typed level |
| TD-18937 | CAD | extend CAD=>Vertex to a tin |
| TD-19230 | CAD | Extra modes for CAD=>Vertex=>Extend by length |
| TD-16594 | CAD | Heads-up display: showing distance/angle/bearing while editing cad lines |
| TD-16721 | CAD | Heads-up display: X, Y, Z when placing point |
| TD-20862 | CAD | Make CAD Leader information Tin Depth support all TIN types |
| TD-16597 | CAD | Make suggested CAD text location snap-able |
| TD-16909 | CAD | Move segment |
| TD-18890 | CAD | new CAD vertex extend 3D to level |
| TD-16596 | CAD | Project settings for Enhanced CAD |
| TD-20471 | Chains | Capture and test the return code of a external exe run from a chain command |
| TD-7973 | Chains | Chain Parameter: Give warning when change command type for loosing all existing parameters |
| TD-19452 | Chains | Command to write parameters to a file |
| TD-20591 | Chains | Commands to control models tins sharing |
| TD-18322 | Chains | Commands to set chain parameter value |
| TD-19231 | Chains | Copy and paste buttons for Chain Parameters Editor panel |
| TD-15325 | Chains | Create model: Transfer field value when tick untick use parameters |
| TD-21722 | Chains | Customising default type for new chain commands |
| TD-14976 | Chains | Delete all project attributes |
| TD-21723 | Chains | Double click to preview chain command |
| TD-15512 | Chains | files and deletes: Transfer field value when tick untick use parameters |
| TD-18892 | Chains | Improve checking number of elements in model |
| TD-18407 | Chains | Include $model_attribute in chain parameters |
| TD-18035 | Chains | Is a project Object Tree or not |
| TD-21641 | Chains | Make chain parameters work with directory box |
| TD-21952 | Chains | Option for HEC-RAS DDA Flooded widths calcs (macro and chain) |
| TD-15864 | Chains | Prevent panels using Property Sheets from being used in Chain Parameters |
| TD-19192 | Chains | Set chain parameter value using an env |
| TD-17855 | Chains, Macro Language | Chain to macro - parameter file of children chain not get read when inherited from parent |
| TD-17854 | Chains, Macro Language | Chain to macro - test idea of new chain command to set chain parameters |
| TD-19360 | Chains, Macro Language | Macro call and chain command check is windows version supporting win11 |
| TD-20221 | Design | Add a project attribute in new pavement manager for largest number of attributes set |
| TD-20305 | Design | Add various features to Calc CL option |
| TD-20575 | Design | Add various features to rail CalcCL option |
| TD-20562 | Design | Add various features to Rail slew calculator option |
| TD-19037 | Design | Create modifiers, layer selection lists were showing silent layers. |
| TD-17148 | Design | Create Z-values from Tin Differences outputs super strings and panel modernisation |
| TD-19235 | Design | Drill and Blast pattern creator |
| TD-18805 | Design | Filter unused edge names from the trimesh edge info structure. |
| TD-21581 | Design | Increase the size of the "Kerb Return Function" panel |
| TD-19682 | Design | MTF Create polygon option to allow selection of the HINGE |
| TD-19684 | Design | MTF Create polygon option to create multiple polygons between 2 links |
| TD-19683 | Design | MTF create polygon with new options for end cap formations |
| TD-21517 | Design | Pavement Manager: Kerb Snippet update to match v14 behaviour |
| TD-19819 | Design | Replaced a panel prompt with new macro call Stockpile Create Macro |
| TD-21585 | Design | Snippets: create tooltips for parameters in pavement snippets |
| TD-21111 | Design | Template Delete: differentiate between project templates and removed templates |
| TD-14951 | Design | Tin Depth Range Polygons - Add option to Clean model of polygons |
| TD-19921 | Design | Tin from trimesh (top bottom) nulling update |
| TD-20634 | Design | Tin from trimesh top/bottom to allow wilcards for name and model |
| TD-20583 | Design | Update of new pavement snippets to reduce the number of layers created |
| TD-17744 | Design | Updates to the Apply MTF Manager |
| TD-21625 | Design | Wildcards for link names defining Named Grades |
| TD-21523 | Design, MTF | Modifier Remove By Pattern, add a remove absolute option |
| TD-21354 | Design, MTF | Named Grade - Normal/Mirror Extra Grades and Min/Max Xfalls |
| TD-16577 | Drafting | Allow update the information tin when editing leader |
| TD-19228 | Drafting | CAD Table from CSV - Allow merging of Header Row |
| TD-17147 | Drafting | Drafting panels to use the full data source |
| TD-19865 | Drafting | Explode data source of drafting elements |
| TD-16657 | Drafting | Information leader with General XYZ and General XY info |
| TD-17028 | Drafting | Leader hook gap work with other text border |
| TD-16304 | Drafting | Remove association of many drafting elements |
| TD-16700 | Drafting | Remove restriction of header merging cell of header line |
| TD-15376 | Drafting | Transform for non associated drafting elements |
| TD-20733 | Drainage | 3d xsection chord interpolation - better error messaging and speed up |
| TD-20613 | Drainage | ARR2019 Il-Cl Dynamic Analysis Method |
| TD-18210 | Drainage | Capture Curve Viewer |
| TD-20402 | Drainage | Capture Curve Viewer: add collapsible group for modifiers |
| TD-20404 | Drainage | Capture Curve Viewer: Call edit_drainage.4d panel from macro not panel prompt |
| TD-20403 | Drainage | Capture Curve Viewer: don't reset font size and point label parameters when changing curves |
| TD-20405 | Drainage | Capture Curve Viewer: Make tooltips parameter-dependent |
| TD-17989 | Drainage | Catchment Creation Tool Using Strings |
| TD-17104 | Drainage | Coding of Concept Stormwater Design option |
| TD-17988 | Drainage | Convert Water strings into Super strings |
| TD-12140 | Drainage | Create Culvert - Help Button and CodeShutdown |
| TD-21090 | Drainage | Create custom list of attributes for use during Dynamic Drainage Analysis run |
| TD-19055 | Drainage | Create drainage.4d from model to load drainage.4d |
| TD-20877 | Drainage | Create hydrograph from peaks now uses attribute groups |
| TD-17388 | Drainage | Create Water Network from Points and Strings |
| TD-14605 | Drainage | Critical Storm label issues for ARR 2019 and not working in non-ARR 2019 |
| TD-19598 | Drainage | CSD: Add "Edit Rainfall File" button to edit_catchments panel |
| TD-19623 | Drainage | CSD: Add "model locked" feedback to Tc Builder panel |
| TD-21302 | Drainage | CSD: Add move functionality as in QWN |
| TD-19622 | Drainage | CSD: Add Pick/Edit button to Tc Builder |
| TD-21303 | Drainage | CSD: Be able to run Rational Analysis |
| TD-21774 | Drainage | CSD: Move/delete functionality like QWN |
| TD-19797 | Drainage | CSD: Show volume on catchment flows graph (NZ SCS requirement) |
| TD-19624 | Drainage | CSD: Tc Builder needs model->Node->catchment->event message |
| TD-19625 | Drainage | CSD: Tc Builder should initially be unpopulated |
| TD-19497 | Drainage | CSD: Warn about zero area when saving catchment data |
| TD-21731 | Drainage | Cut/copy/paste to/from grids in drainage.4d editor |
| TD-15913 | Drainage | DDA - Create EPA-SWMM file from DDA |
| TD-15998 | Drainage | DDA - FHWA weir needs to handle overtopping |
| TD-16019 | Drainage | DDA - FHWA Weirs need to report DS depth |
| TD-17119 | Drainage | DDA - Generate warning/error for duplicate link names |
| TD-15633 | Drainage | DDA - Make Shape summary in .rpt file optional |
| TD-17532 | Drainage | DDA - Messages regarding Grade and Xfall are only valid for On-grade pits |
| TD-15568 | Drainage | DDA - Trap and report undefined link names |
| TD-15567 | Drainage | DDA - Trap and report undefined sump levels |
| TD-17113 | Drainage | DDA - WNE add arguments to allow startup on a particular tab, auto-solve etc |
| TD-15940 | Drainage | DDA add dyn min surface area - defaults and overrides |
| TD-17146 | Drainage | DDA Box plot, Critical storm and Durations critical storms graphs should only use data from current run |
| TD-17617 | Drainage | DDA improved message when design frequency is outside range defined in hydro file |
| TD-13675 | Drainage | DDA Report Weir Cd at the maximum flow |
| TD-20642 | Drainage | DDA will not run with hydro file ARI from and to values the same |
| TD-19841 | Drainage | DDA: Add error messages when Drainage_Network connectivity is invalid |
| TD-19234 | Drainage | DDA: calculated ku method attribute set with both text and integer values |
| TD-16087 | Drainage | DDA: Change default INERTIAL_DAMPING from NONE to PARTIAL |
| TD-19850 | Drainage | DDA: Change Variable temporal patterns to support sub 1 minute rainfall data |
| TD-21402 | Drainage | DDA: Create plan plots and long-section profiles using attribute groups |
| TD-17215 | Drainage | DDA: Delete submergence ratio attribute before dda run |
| TD-15997 | Drainage | DDA: FHWA weir needs to transition Cd between "shallow" and "deep" curves |
| TD-14304 | Drainage | DDA: Flooded width calcs |
| TD-16043 | Drainage | DDA: Graph Cd for Weirs |
| TD-20782 | Drainage | DDA: Improve loading of info/warning/error messages on completion of analysis (Build 192) |
| TD-15447 | Drainage | DDA: Lost flows should be reported as an error at the end of the simulation |
| TD-19597 | Drainage | DDA: Replace US/DS invert elev with start/Stop elev for pump graphs |
| TD-16086 | Drainage | DDA: RTP to HTML converter needs to account for Froude and Cd in header |
| TD-19429 | Drainage | DDA: Show runoff volume on rainfall runoff graph for Drains users |
| TD-17271 | Drainage | DDA: Sort graphs by duration not solved order |
| TD-19663 | Drainage | DDA: Tables in the html reports to have sticky headers and hover highlighting |
| TD-2873 | Drainage | DNE documentation of tabs and input fields |
| TD-16162 | Drainage | Drainage HTML reports panel - title update to include capitals |
| TD-17272 | Drainage | Drainage to zip: Clear console removed |
| TD-15731 | Drainage | drainage.4d load on demand |
| TD-21162 | Drainage | DWS: Rule/control builder called from another macro |
| TD-16384 | Drainage | Dynamic Culvert - Add Tide Gate flag to prevent culvert backflow |
| TD-15945 | Drainage | Dynamic Culvert - Set INERTIAL_DAMPING = PARTIAL |
| TD-628 | Drainage | Dynamic Drainage - Use pit capture curves at either end of a basin link to control basin discharge |
| TD-16088 | Drainage | Dynamic Graphs - Add "Clear Selections" button |
| TD-20792 | Drainage | HECRAS 6.3.1 for dynamic flooded width added |
| TD-21798 | Drainage | HEC-RAS 6.4 and 6.4.1 for flooded widths |
| TD-15060 | Drainage | Hydro file macro call - get storm by id implemented for ARR 2016 bins |
| TD-15424 | Drainage | Inlet Capacity Panel - prevent 0 road grade and crossfall |
| TD-20332 | Drainage | Inlet Capture Curves: create separate fields for flow and depth ranges (and documentation) |
| TD-18416 | Drainage | Inlet curves panel (HEC-22). Add button to link to capture curve viewer option |
| TD-10175 | Drainage | Link Critical Froude number stored as a link attribute |
| TD-18878 | Drainage | Node riser display in perspective opengl |
| TD-21724 | Drainage | Place node markers - offset distance option |
| TD-16139 | Drainage | Project Settings - Water String Chord to Arc setting |
| TD-20698 | Drainage | QWN move individual pipes |
| TD-21154 | Drainage | QWN: Change 'Default Elevation' to be anything other than '-null' |
| TD-21153 | Drainage | QWN: Change the order of the information in QWN Startup to match Water Defaults |
| TD-21208 | Drainage | QWN: Changes to default panel |
| TD-21151 | Drainage | QWN: Enhance QWN to allow the model for Bypass Lines to be specified by the user or populate relevant field |
| TD-20006 | Drainage | QWN: Finalise panels for editing/deleting of nodes/links |
| TD-21152 | Drainage | QWN: Reduce confusion about what 'Override Defaults?' does |
| TD-21956 | Drainage | Regrade links log line messages with reference info |
| TD-18018 | Drainage | Time of Concentration Builder |
| TD-15401 | Drainage | Triangulate grate levels |
| TD-15501 | Drainage | Use a default inlet rating curve if road xfall and road grade are unknown or outside the range in the drai |
| TD-21573 | Drainage | Water House Connections to BIM |
| TD-16875 | Drainage | Water Hydro file to have 20 columns in the ifd table |
| TD-21005 | Drainage | Water String: check if Trimesh Rotation Att is "Input/output null height" and set to NULL |
| TD-315 | Drainage | WNE always allow create from Import |
| TD-16832 | Drainage | WNE choice box to set allow clear property set to true |
| TD-19718 | Drainage | WNE construction drainage data model to be updated for Object Tree naming |
| TD-17266 | Drainage | WNE Cover RL and Grate RL not updating on Set Node Details if values that were previously entered are not valid |
| TD-15626 | Drainage | WNE Import/Export to export multiple diverging ds pipes |
| TD-17307 | Drainage | WNE Single Node for FW Bypass |
| TD-17878 | Drainage | WNE: New widget arrangement in navigation (top) section |
| TD-17879 | Drainage | WNE: Replace old terminology. Pits/Pipes with Nodes/Links etc. |
| TD-14350 | Drainage | WNE: Slight shuffle of fields for efficiency gains |
| TD-15400 | Drainage | WNE: speed up load time of water model |
| TD-14192 | Drainage | WQ: Create attribute groups for Infiltration System Treatment process |
| TD-14199 | Drainage | WQ: Create Generic Treatment process |
| TD-14200 | Drainage | WQ: Create Junction Node |
| TD-14061 | Drainage | WQ: Create Link Node network from Music MSF File |
| TD-14202 | Drainage | WQ: Create Primary Link |
| TD-14198 | Drainage | WQ: Create Rainwater Tank Treatment process |
| TD-14201 | Drainage | WQ: Create Receiving Water Node |
| TD-14204 | Drainage | WQ: Create Secondary Link |
| TD-14064 | Drainage | WQ: Results graph enhancements |
| TD-18377 | Drainage 2D | 12d channel earthwork designs to TUFLOW ESTRY |
| TD-19342 | Drainage 2D | 1d approach flow and catchment strings extend/shorten |
| TD-21296 | Drainage 2D | 2D Catchment flow lines (SA - source area) - distribute flow to all cells |
| TD-21467 | Drainage 2D | 2D Quick Analysis - WaterRide Format |
| TD-21071 | Drainage 2D | 2D result tin to use default settings for read results |
| TD-22061 | Drainage 2D | 2D TUFLOW dt and FLT Map output commands added |
| TD-19755 | Drainage 2D | Add ability to run multiple tcf files from TCF editor |
| TD-19706 | Drainage 2D | Attributes to/from clip board CodeShutDown and tick box for creating empty text attributes |
| TD-21132 | Drainage 2D | Change panel name from Roadflow to 2D Quick Analysis |
| TD-16605 | Drainage 2D | Create Empty Models missing help button |
| TD-21096 | Drainage 2D | DDA 2D messages: remove duplicates and create groups |
| TD-16716 | Drainage 2D | DDA 2D: Changes to support Tuflow release 2020 10 AA |
| TD-16351 | Drainage 2D | DDA-2D - Link with Tuflow 2020-08-ZA then ZB |
| TD-15850 | Drainage 2D | DDA2D - Update to Tuflow libraries 2020-06-ZA |
| TD-15921 | Drainage 2D | DDA2D - Update to Tuflow libraries 2020-06-ZB |
| TD-17531 | Drainage 2D | DDA2D: Add grate depth tolerance for 2d approach flow |
| TD-15691 | Drainage 2D | Drainage 2d sx connection zone - move node xy not end of string |
| TD-16877 | Drainage 2D | Open GL View: Tile: Have it work for this view type |
| TD-19170 | Drainage 2D | Quadtree to run without SGS |
| TD-15996 | Drainage 2D | Read TUFLOW QuadTree TMO and TGO files |
| TD-18819 | Drainage 2D | Reduce DDA2d output window messages |
| TD-19081 | Drainage 2D | Roadflow Direct Rainfall Variable temporal patterns for NZ implemented |
| TD-20528 | Drainage 2D | Roadflow: add flt output command for ARR 2019 elev, depth and hazard |
| TD-19348 | Drainage 2D | Roadflow: Laurenson Hydrology Method Added |
| TD-16423 | Drainage 2D | Set tuflow_quadtree_tests_4d on by default |
| TD-12316 | Drainage 2D | String Attribute IO to spreadsheet to have delete option on import |
| TD-20602 | Drainage 2D | TCF direct rainfall update tickbox |
| TD-15812 | Drainage 2D | TCF editor - disable DP for GPU |
| TD-10943 | Drainage 2D | TCF Editor command line options for Direct Rainfall |
| TD-18962 | Drainage 2D | TCF Editor to allow empty models |
| TD-19082 | Drainage 2D | TCF Quad tree 3+ level grid tin complete |
| TD-18794 | Drainage 2D | TCF Quadtree - Add method to link and validate xf files to 12d grid tins |
| TD-19164 | Drainage 2D | TCF Quadtree to skip writting xf file for qpp runs |
| TD-16182 | Drainage 2D | Time Lines - Allow TGO results |
| TD-20837 | Drainage 2D | TUFLOW 2020-10-AF Patch Release |
| TD-18489 | Drainage 2D | TUFLOW 2020-AB Release |
| TD-22047 | Drainage 2D | TUFLOW 2023 03 AC update |
| TD-21394 | Drainage 2D | TUFLOW 23-03-AB Release Update |
| TD-20672 | Drainage 2D | TUFLOW AE version update |
| TD-17174 | Drainage 2D | TUFLOW command file to lower case |
| TD-16158 | Drainage 2D | TUFLOW Command Update for QuadTree |
| TD-19070 | Drainage 2D | TUFLOW exe and DLL update to 2020-10-AC |
| TD-20347 | Drainage 2D | TUFLOW exe and DLL update to 2020-10-AD |
| TD-15965 | Drainage 2D | TUFLOW Quad Tree and SGS Commands |
| TD-17071 | Drainage 2D | TUFLOW QuadTree TMO Grid Tin Display |
| TD-17400 | Drainage 2D | TUFLOW SGS to Roadflow and TCF |
| TD-4459 | Drainage 2D | TUFLOW Tin Results Settings to show only available results |
| TD-15761 | Drainage 2D | TUFLOW update to June 2019 Version |
| TD-18378 | Drainage 2D | TUFLOW: 1d channel import |
| TD-18379 | Drainage 2D | TUFLOW: culvert export |
| TD-18380 | Drainage 2D | TUFLOW: ESTRY 1D visualisation |
| TD-17419 | Drainage 2D | Use new projection-MapInfo File in TCF editor |
| TD-19200 | Drainage, Drainage 2D | DDA: Speed up of starting analysis when reading very large drainage.4d file |
| TD-20032 | Drainage, Drainage 2D | Update setting hydro box code |
| TD-17110 | Drainage, Drainage 2D | WNE: Sag Pit from global to local |
| TD-15634 | Drainage, Dynamic Water Supply | Add error messages to EPA-SWMM/NET import |
| TD-16411 | Drainage, Dynamic Water Supply, Sewer | Water string purpose routine needs water supply |
| TD-20716 | Dynamic Water Supply | Concept Water Supply |
| TD-18481 | Dynamic Water Supply | Incorporating the DWS Rule/Control builder into the WNE |
| TD-15714 | Dynamic Water Supply | Solve for multiple demands at a node |
| TD-15713 | Dynamic Water Supply | Support multiple demands at a node |
| TD-18913 | EPlan | Traverse Spreadsheet Object Tree aware |
| TD-16894 | File I/O | 12d Writer: export of super tins to include component tins |
| TD-15222 | File I/O | 12d Writer: new choice to output only tins and cloud string in hex floats |
| TD-19517 | File I/O | Add Cant Information to LandXML Output File |
| TD-15723 | File I/O | Add model attributes choice to write 12da xml panels - step 1 |
| TD-13314 | File I/O | Add new DGN2020 64 bit engine for reading DGN |
| TD-18994 | File I/O | Add support for filenames over 260 characters |
| TD-15766 | File I/O | Add user options in reading in model attributes from 12da |
| TD-21007 | File I/O | Allow the word NULL for a null value in 12da/12dXML files |
| TD-21928 | File I/O | Another case for repairing LAS headers |
| TD-18626 | File I/O | ARCViewShape readers: populate attribute list by default |
| TD-17930 | File I/O | Disable older DGN DWG reader engines and default to 2020 64bit |
| TD-22273 | File I/O | Drag and drop for DGN files |
| TD-15127 | File I/O | KML reader: rewrite as hard code |
| TD-17330 | File I/O | LandXML 1.2 reader: read in drainage strings |
| TD-21520 | File I/O | Landxml read: Read rail cant data |
| TD-20979 | File I/O | Landxml write: output file includes the type of transition mapping file used |
| TD-17411 | File I/O | Mapinfo write panel use new projection box |
| TD-18625 | File I/O | Mid/mif readers: populate attribute list by default |
| TD-19544 | File I/O | New choice to read general XYZ as separate points |
| TD-18122 | File I/O | Options to Convert between Ascii and Binary XML |
| TD-20586 | File I/O | Output to LandXML allow user to choose LandXML version |
| TD-19922 | File I/O | Read binary STL file with colours |
| TD-19546 | File I/O | Read STL file |
| TD-15830 | File I/O | Reading 12da/xml with already existing tins |
| TD-20314 | File I/O | Remove restriction on character length for Model name when reading a Genio |
| TD-17023 | File I/O | Write 12da/12dXML: Ouput super tin components |
| TD-18405 | File I/O | Write Collada DAE add normal vectors and up direction |
| TD-19543 | File I/O | Write Collada DAE tweaks |
| TD-12536 | File I/O | xyz general - pre postfix field - warning message |
| TD-19576 | GIS | GIS Interface to WMTS (Web Map Tile Service) |
| TD-21972 | GIS | GIS menu rearranged |
| TD-20774 | GIS | Option to access feature data using REST service |
| TD-21137 | GIS | Option to access WFS data |
| TD-21136 | GIS | Option to access WMS data |
| TD-15844 | IFC | "header" information |
| TD-16880 | IFC | Add support for Undo after IFC Read |
| TD-16737 | IFC | IFC Express Writer: Exclude 'network' attribute group for IFC export in water strings |
| TD-20181 | IFC | IFC Read: Panel field for null z-value |
| TD-15215 | IFC | IFC Reader: Add Label style to Alignment tab |
| TD-17600 | IFC | IFC Reader: Read in tin breaklines |
| TD-15216 | IFC | IFC Reader: Tick on Alignment to keep both strings |
| TD-17738 | IFC | IFC Writer: Add (X,Y) rotation to Placement Tab |
| TD-15122 | IFC | IFC Writer: Add Coordinate Reference System tab |
| TD-15716 | IFC | IFC Writer: Add schema for 4.3 to IFC Writer |
| TD-15572 | IFC | IFC Writer: Add tick to not break up segments of super strings |
| TD-15500 | IFC | IFC Writer: Add tickbox to choose to export strings as extrusions along a path in IFC4 and IFC4x1 |
| TD-16450 | IFC | IFC Writer: Allow tins to have any IfcElement type |
| TD-15842 | IFC | ifc Writer: Attribute group for ifc BuiltElement parameters |
| TD-15843 | IFC | IFC Writer: Attribute group for ifc Element Assembly parameters |
| TD-18366 | IFC | IFC Writer: CAD Circle |
| TD-17951 | IFC | IFC Writer: Change drainage to water |
| TD-16455 | IFC | IFC writer: Control default debugging attributes with 'Ifc_Default_Atts' environment variable |
| TD-15806 | IFC | IFC Writer: Export 12d Assembly Elements |
| TD-15391 | IFC | IFC Writer: Export extruded strings using IfcExtrudeAreaSolid with arbitrary profile |
| TD-17426 | IFC | IFC Writer: Export Project attributes |
| TD-15528 | IFC | IFC Writer: Include model name in spatial structure entities |
| TD-15841 | IFC | ifc: Attributes for Spatial Structure tree and name |
| TD-15847 | IFC | ifc: ifcElement Attributes for Description |
| TD-17513 | IFC | IFCPRESENTATIONLAYERASSIGNMENT |
| TD-20118 | IFC | Read many option for IFC reader |
| TD-16558 | IFC | Set the Output Drainage as IFC System to be ticked by default |
| TD-19024 | IFC | Use IFC Presentation Layers for Models |
| TD-17138 | IFC | Writer: Property Sets for top attribute groups |
| TD-15065 | Installation | Added a tickbox to install trimble precision runtime during installation |
| TD-17465 | Installation | Auto Updater - Allow custom download location with env var |
| TD-17437 | Installation | Auto Updater - Auto Cleanup exe's |
| TD-17436 | Installation | Auto Updater - Naming scheme for downloaded exe's |
| TD-18275 | Installation | Auto Updater: Check for open sessions of 12d model before starting download |
| TD-18421 | Installation | Auto Updater: Error messages when running auto-updater |
| TD-18276 | Installation | Auto Updater: Removed all downloaded exe's after successful installation |
| TD-18382 | Installation | Auto-Updater: Check if new version is available before showing panel |
| TD-17069 | Installation | AutoUpdater: in depth checking for running instances |
| TD-18128 | Installation | Disk Space checks for Auto Updator |
| TD-19157 | Installation | Installer for 12d Model: add the latest CodeMeter install program to the 12d installer |
| TD-16809 | Installation | Monitor and report on installation to user |
| TD-17122 | Installation | Silent install for Trimble precision SDK Redistributable in installation |
| TD-19027 | Macro Language | 12dPL Choice Box: flag to define which search type |
| TD-20928 | Macro Language | 2D drop to a polymesh face |
| TD-17926 | Macro Language | 2D Helmert |
| TD-17924 | Macro Language | 2D Helmert parameters from a list of points |
| TD-17925 | Macro Language | 3D Helmert parameters from a list of points |
| TD-20751 | Macro Language | Add a Weight_Box to the macro language |
| TD-16995 | Macro Language | Add fuzzy logic calls to macro language |
| TD-16966 | Macro Language | Add macro calls to set sizing options of widgets |
| TD-19264 | Macro Language | add pattern to File_Box |
| TD-20183 | Macro Language | Add some macros calls to calculate checksums of GPS NMEA strings |
| TD-19667 | Macro Language | Add vertex at the end of super string |
| TD-16302 | Macro Language | Additional macro calls for Process_Handle |
| TD-16969 | Macro Language | Allow macro panels to set the dynamic_sizing property for widget pages |
| TD-21908 | Macro Language | Call for GridCtrl_Box to return the cell row and column of focus |
| TD-20213 | Macro Language | Call for tin from trimesh (top and or bottom) |
| TD-20117 | Macro Language | Call for uploading a script to a GPS receiver |
| TD-21106 | Macro Language | Call to access the modern function for parsing text lines in words |
| TD-21126 | Macro Language | Call to convert real number to text supporting negative precision |
| TD-20230 | Macro Language | call to flip all faces of a trimesh |
| TD-20235 | Macro Language | Call to split drainage strings |
| TD-20130 | Macro Language | Call to write metadata to xml files |
| TD-20251 | Macro Language | calls to draw element and model that work better in threaded views |
| TD-20381 | Macro Language | Calls to draw elements in one view |
| TD-19674 | Macro Language | Change widget tooltip |
| TD-11957 | Macro Language | Check attributes |
| TD-21274 | Macro Language | Check for real being null or minus null |
| TD-20945 | Macro Language | Check if a polygon is planar |
| TD-20607 | Macro Language | Control models tins sharing |
| TD-21975 | Macro Language | Convert text to legal XML text |
| TD-19833 | Macro Language | Convert Trimesh Named Faces to Polymesh |
| TD-21204 | Macro Language | Convert uid to 64bit Integer |
| TD-21515 | Macro Language | Cookie cut trimesh using a polygon |
| TD-16963 | Macro Language | Create a file box with description |
| TD-15664 | Macro Language | Create Macro Null() for a Drainage_Network object |
| TD-19802 | Macro Language | Create polymesh from existing trimesh |
| TD-18236 | Macro Language | Create_macro_as_child calls to pass down and retrieve macro attributes from the child macro |
| TD-21536 | Macro Language | Create_strings_from_sections |
| TD-18133 | Macro Language | Creating polymesh for "Planar Polygons to trimesh" call |
| TD-19029 | Macro Language | Creating polymesh for Planar Polygons to trimesh |
| TD-16958 | Macro Language | Cut/fill Trimesh |
| TD-20750 | Macro Language | Delete drainage nodes |
| TD-18616 | Macro Language | Delete empty models call with check for model attributes |
| TD-21834 | Macro Language | Delete model and tin with optional check for share out |
| TD-16964 | Macro Language | Disable macro panel chainability |
| TD-17257 | Macro Language | Disjoint Trimesh |
| TD-19389 | Macro Language | Drop point to trimesh |
| TD-20596 | Macro Language | Ellipsoid distances from plan distances |
| TD-21903 | Macro Language | Enable spell checking for Text Edit Box |
| TD-19864 | Macro Language | Explode drafting elements |
| TD-18097 | Macro Language | Explode text |
| TD-18223 | Macro Language | Explode text border |
| TD-18254 | Macro Language | Fence macro calls to work with trimeshes |
| TD-18637 | Macro Language | Find a system file without giving an Output Window message if it is not found |
| TD-19899 | Macro Language | Flip 1 trimesh face, array of trimesh faces and all trimesh faces |
| TD-21522 | Macro Language | Form_trimesh_from_polygon |
| TD-16960 | Macro Language | General call to read files ending with 12da, 12daz, 12dxml or 12dxmlz |
| TD-14983 | Macro Language | Get and set allow holes property of polygon box |
| TD-19096 | Macro Language | Get and set property controls for a Water String |
| TD-19199 | Macro Language | Get and set trimesh solid |
| TD-18265 | Macro Language | Get equality chainage from raw chainage |
| TD-16470 | Macro Language | Get file times: created, modified, accessed |
| TD-18431 | Macro Language | Get geodetic datum data |
| TD-19603 | Macro Language | Get geodetic projection datum names should combine information from different files as the box |
| TD-16218 | Macro Language | Get nodes/links by purpose from drainage.4d |
| TD-16965 | Macro Language | Get point scale factor and nvalue |
| TD-18266 | Macro Language | Get raw chainage from equality chainage |
| TD-19665 | Macro Language | Get set Perspective view eye target |
| TD-19664 | Macro Language | Get set Plan view viewport |
| TD-19666 | Macro Language | Get set Section view viewport |
| TD-19905 | Macro Language | Get signed volume of a trimesh |
| TD-20753 | Macro Language | Get the absolute path from relative path |
| TD-19028 | Macro Language | Get the chainage for the nth vertex of a string |
| TD-21234 | Macro Language | Get the chainage-height profile for a string |
| TD-18995 | Macro Language | Get the number of elements in a model with less model loading |
| TD-20780 | Macro Language | Get the type of an XML Node |
| TD-19252 | Macro Language | get view placement |
| TD-19691 | Macro Language | Get view usable area |
| TD-19803 | Macro Language | Get_12dmodel_version(Integer &major,Integer &minor,Text &patch) |
| TD-20492 | Macro Language | Get_drainage_network_upstream_pipes and Get_drainage_network_downstream_pipes |
| TD-19418 | Macro Language | Get_elements |
| TD-18015 | Macro Language | Get_license_client |
| TD-16895 | Macro Language | Get-Set_drainage_pit_riser |
| TD-17528 | Macro Language | Gridctrl_Box - function for set cell colour |
| TD-17256 | Macro Language | Heal Trimesh |
| TD-21619 | Macro Language | Highlight points, lines and arcs on view |
| TD-20749 | Macro Language | Insert drainage nodes |
| TD-19809 | Macro Language | Integer Get_file_read_only and Integer Set_file_read_only |
| TD-16957 | Macro Language | Intersection of straight line with an element |
| TD-18036 | Macro Language | Is a project Object Tree or not |
| TD-17250 | Macro Language | Join Water string |
| TD-21934 | Macro Language | List files/folders in a directory |
| TD-19967 | Macro Language | Macro call to run TUFLOW via tcf |
| TD-16469 | Macro Language | Macro language support for STL like containers |
| TD-20669 | Macro Language | Measure NZ Grid Azimuth |
| TD-20668 | Macro Language | Model_attribute_delete_all() has a dummy argument |
| TD-20952 | Macro Language | Move_attributes |
| TD-16897 | Macro Language | One call to read 12da, 12daz, 12dxml, 12dxmlz file format |
| TD-16961 | Macro Language | One write call based on file extension 12da, 12daz, 12dxml, 12dxmlz |
| TD-19290 | Macro Language | Panel_prompt does not need to display macro console |
| TD-14875 | Macro Language | Panel_prompt now supports SLX format data |
| TD-19026 | Macro Language | Plan distance between two coords |
| TD-19649 | Macro Language | Projection box |
| TD-17469 | Macro Language | Read 12da 12dxml with choices for model and project attributes |
| TD-19288 | Macro Language | Read only files and converting SDR function from FLD to 12dField |
| TD-20752 | Macro Language | Read STL file |
| TD-17475 | Macro Language | Remove a tin out of a containing model |
| TD-21891 | Macro Language | Remove share out status of models |
| TD-21836 | Macro Language | Remove share out status of tins |
| TD-20933 | Macro Language | Replace an element |
| TD-17406 | Macro Language | Return the local path of an existing Synergy folder |
| TD-17864 | Macro Language | Return the name for files of model, tin, view on disk |
| TD-21236 | Macro Language | Save and read output window to XML |
| TD-21200 | Macro Language | Set border style of text style data |
| TD-21890 | Macro Language | Set highlight linestyle and weight |
| TD-18893 | Macro Language | Set trimesh edge by string |
| TD-21833 | Macro Language | Share in tin to current project with specified model |
| TD-14441 | Macro Language | smart chainages calls |
| TD-19030 | Macro Language | Source box Access to process only selected vertices |
| TD-19955 | Macro Language | Tin area at level to work with supertin |
| TD-19954 | Macro Language | Tin_Plan_Area_At_Elevation now works for supertins. |
| TD-18096 | Macro Language | Updates to Trimesh and Line_cut_string |
| TD-21209 | Macro Language | Write 12d data calls: extend the bool flags to cover the new choice of output null keyword |
| TD-21237 | Macro Language | Write 12d data macro calls, extend the bool flags to cover the new choice of output hex float for TIN |
| TD-21238 | Macro Language | Write 12d data macro calls, extend the bool flags to cover the new choice of output null attributes |
| TD-16959 | Macro Language | Write 12da, 12daz, 12dxml, 12dxmlz files |
| TD-18406 | Macro Language | Write Collada DAE files |
| TD-21235 | Macro Language | xy_inside(Element polygon,Real x,Real y) |
| TD-18482 | MTF | Add attribute manipulator modifier |
| TD-18645 | MTF | Add default behaviour for named grades when link/s don't exist. |
| TD-20146 | MTF | Add Duplicate to list of options in the modifiers edit panel |
| TD-20483 | MTF | Add lowest and highest chainage attributes to MTF strings |
| TD-21648 | MTF | Add side resolving syntax "=>" for smart chainage "Intersection of a Link" |
| TD-21033 | MTF | Adding wildcard support for modifier: "Decision String Exists" |
| TD-20484 | MTF | Allow snippet widgets to have tooltips |
| TD-20943 | MTF | Allow user to overide default section width for modifier: "Reinterface Tin" |
| TD-20822 | MTF | Allow user to override default section width for modifier: "Fixed Link - To Tin" |
| TD-18490 | MTF | Apply attributes, add length from start/end chainage |
| TD-21030 | MTF | Apply MTF, populate function name and auto load apply defaults on centreline select. |
| TD-18502 | MTF | Copy layer, should allow link insert whey same offset but different height. |
| TD-18621 | MTF | Create MTF Seed file Menu tool |
| TD-16352 | MTF | Create strings/sections/tins, make strings/sections optional |
| TD-20208 | MTF | Link intersect tin documentation needed clarification. |
| TD-21528 | MTF | Modifier: Intersect Links with Link |
| TD-16826 | MTF | Modify by 2 links should not care if multiple strings found |
| TD-20582 | MTF | Modify Manipulate Attribute now available in a panel and documented |
| TD-19608 | MTF | Modify to string, add "Current side" choice |
| TD-20649 | MTF | Modify to trimesh, allow multiple trimeshes of the same name |
| TD-20065 | MTF | MTF create string, trimeshes, select links from layers grid control update |
| TD-20090 | MTF | MTF Decision String Exists section width |
| TD-19485 | MTF | MTF not supporting use of some string types. |
| TD-18082 | MTF | MTF: Speed up snippet processing. |
| TD-19615 | MTF | Named grade adding spurious 'on fail' message to output window |
| TD-19610 | MTF | Named grade: allow link and side to be added twice |
| TD-20715 | MTF | New default for "Modify - Link to tin" is now "Modify height, hold width" |
| TD-20916 | MTF | New intersection cut number for smart chainages: "Intersect strings" & "Cut ref with other string" |
| TD-21003 | MTF | New modifier "Fixed - Remove by pattern" |
| TD-20917 | MTF | New syntax to define snippet parameters on multiple lines |
| TD-19969 | MTF | Open variable links trimesh was missing last named edge information |
| TD-19565 | MTF | Smart chainages, add max left, right offsets to snippet from model of strings |
| TD-17498 | MTF | Smart Special Chainage File |
| TD-17943 | MTF | Snippet AutoParameter : _MODEL_ATTRIBUTE |
| TD-21103 | MTF | Snippet call "set_model_attribute" updated to create the model if it does not yet exist |
| TD-21108 | MTF | Snippet call "set_project_attribute" parameters now allow token substitution |
| TD-15035 | MTF | Snippets, add call to delete a project attribute |
| TD-17618 | MTF | Template modifiers panel, add 'Edit modifier' to right click choice list |
| TD-21485 | MTF | Update Pretty Description of the Fixed Decision Modifiers |
| TD-19473 | Other | AutoUpdater - Allow copy from the log box |
| TD-17897 | Other | UsageLog to report 12d model version number |
| TD-15145 | Plotting | Add model name as PDF layer of plan frame of MPS |
| TD-15635 | Plotting | allow literal "$" from a TBF or drawing register |
| TD-17907 | Plotting | Better error messages for CSV Drawing Register |
| TD-17915 | Plotting | Change corridor labeling column name from "Create Set #" to "Define Set #" |
| TD-19209 | Plotting | Cuts: Warning message in output window for labels that won't fit |
| TD-15338 | Plotting | Extra TBVs for Water Node Diagram PPF |
| TD-21359 | Plotting | Implement raster DPI from plotter definition in output PDF |
| TD-16405 | Plotting | L Sect Plot: Simplified Extensive V when Vertical Part Type is Fixed Points Computator |
| TD-19462 | Plotting | Linestyle of Grids on Drainage Long plots, Long plots and X section plots |
| TD-21728 | Plotting | Long Section plot - Cuts: be able to specify the labelling of the Height of a cut string |
| TD-17263 | Plotting | Long Section Plotting - Change panel wording of 'Convert to super alignment for plotting' option |
| TD-19461 | Plotting | Long Section Plotting: Add chainage range attributes when plotting to model |
| TD-18496 | Plotting | Long Section: Tin titles length automatically shrinks to size like X Section does |
| TD-17968 | Plotting | LPlot PPF: Corridor Model Draw Order buttons |
| TD-21932 | Plotting | LS plot with plan component to allow primary with no VG |
| TD-17972 | Plotting | Melbourne LPlot PPF: Corridor Model Draw Order buttons |
| TD-15639 | Plotting | MPS - Highlight active viewport weight |
| TD-16048 | Plotting | MPS - Improved Multi Node pre plotting structure checks |
| TD-17452 | Plotting | MPS - Long Section - Ignore String to profile IDs when reading from library file |
| TD-17309 | Plotting | MPS - Long Section Plot - Simplified Extensive V when Vertical Part Type is Fixed Points Computator |
| TD-14799 | Plotting | MPS - Loose ordering of Nodes by default to match standard workflow |
| TD-15638 | Plotting | MPS - Make 'Plotter type' field inherited |
| TD-14893 | Plotting | MPS - minor changes/improvements for pre plotting check messages |
| TD-15340 | Plotting | MPS - New text $variable - $folder |
| TD-15339 | Plotting | MPS - New text $variable - $project |
| TD-16242 | Plotting | MPS - Perspective Frame Dynamic View Details |
| TD-14735 | Plotting | MPS - Remove misleading standard plotting progress messages |
| TD-16346 | Plotting | MPS - Section Frame Dynamic View Details |
| TD-16334 | Plotting | MPS - Smarter Copy/Paste handling of 'use to populate title block' Frame field |
| TD-15337 | Plotting | MPS default value changes for the NZ boys |
| TD-19963 | Plotting | MPS preview remove the unused raster loading |
| TD-16601 | Plotting | MPS: key to be an alternate button for accepting positions |
| TD-16393 | Plotting | MPS: 3D PDF Frame Dynamic View Details |
| TD-16724 | Plotting | MPS: Escaping delete Node pop-up should select No instead of Yes |
| TD-16600 | Plotting | MPS: Frame View Details 'view' field naming tweaks |
| TD-16416 | Plotting | MPS: Inheritance for 3D PDF Frame Reference Node View Details |
| TD-16232 | Plotting | MPS: Inheritance for 3D PDF Frame Reference Nodes |
| TD-16127 | Plotting | MPS: Inheritance for Frame Reference Node Margins |
| TD-16034 | Plotting | MPS: Inheritance for Model Reference Nodes |
| TD-16347 | Plotting | MPS: Inheritance for Perspective Frame Reference Node View Details |
| TD-16230 | Plotting | MPS: Inheritance for Perspective Frame Reference Nodes |
| TD-16233 | Plotting | MPS: Inheritance for Plan Frame Reference Node View Details |
| TD-16126 | Plotting | MPS: Inheritance for Plan Frame Reference Nodes |
| TD-16348 | Plotting | MPS: Inheritance for Section Frame Reference Node View Details |
| TD-16231 | Plotting | MPS: Inheritance for Section Frame Reference Nodes |
| TD-16035 | Plotting | MPS: Inheritance for Symbol Reference Nodes |
| TD-19519 | Plotting | MPS: Model Node Centre Data Button |
| TD-19127 | Plotting | MPS: More progress messages while navigating |
| TD-20823 | Plotting | MPS: Plotter override if defined at the chapter or page level |
| TD-15636 | Plotting | MPS: Prompt to save current configuration if unsaved changes present when reading in a .12dmpsf |
| TD-15136 | Plotting | MPS: Remove underscores from Plot mode field choices |
| TD-19463 | Plotting | MPS: Text Node $variable - $if_next_page<> and $if_previous_page<> |
| TD-19465 | Plotting | MPS: Text Node $variable - $node_name |
| TD-16406 | Plotting | MPS: Text Node $variables - 4 $variables for chapter page numbers |
| TD-14697 | Plotting | MPS: Title Block tick box for use of scales in MPS Frames |
| TD-18492 | Plotting | MPS: Title Block: Stop OPW spam of 'File not found' messages while navigating |
| TD-14798 | Plotting | MPS: Warning when Title Block appears before populating Frame |
| TD-15425 | Plotting | MPS: Water Node Diagram Frame - Network model override |
| TD-15342 | Plotting | MPS:Remove Active Tick Box from Book Node |
| TD-17970 | Plotting | Pipeline LPlot PPF: Corridor Model Draw Order buttons |
| TD-20416 | Plotting | Plots: 12d archive files for Models in plot units |
| TD-18495 | Plotting | Plotting: Title Block: Drawing Register: Add .xlsm extension to 'Register file' browse |
| TD-19441 | Plotting | PPF Editors: Grid Control Box Toolbar |
| TD-20161 | Plotting | Section long plot, add offset line style to box => offset string grid |
| TD-21702 | Plotting | Set weight to conduit width based on a specified plot scale |
| TD-17969 | Plotting | Water LPlot PPF: Corridor Model Draw Order buttons |
| TD-15336 | Plotting | Water Node Diagrams plot - node order |
| TD-15335 | Plotting | Water Node Diagrams plot - water model override in MPS special chapter |
| TD-15341 | Plotting | X Section Plotting: Title Block $variable - $model_name |
| TD-17971 | Plotting | XPlot PPF: Corridor Model Draw Order buttons |
| TD-18376 | Rivers | River xsection interpolation using chords |
| TD-15081 | Sewer | Sewer: Recalc PCs and Create HCs for entire sewer model |
| TD-21660 | Sharing | Add Shared Tins To Project to better handle existing Shared in Tins |
| TD-20794 | Sharing | Master Share File no longer compresses multiple spaces |
| TD-19315 | Sharing | Project =>Sharing: mods to the menu |
| TD-19400 | Sharing | Share colours for object tree |
| TD-19908 | Sharing | Share manager: convert master shares to direct shares |
| TD-11456 | Sharing | Sharing of super tins |
| TD-16266 | Standard strings | Create Grid String does not use keep the messages flowing |
| TD-16977 | Standard strings | SS Editor: String attributes |
| TD-16976 | Standard strings | Super string Create: "not specified", " general" and "no height" as "String type" choices |
| TD-21580 | Super Alignment | "Edit & Sameas" button on the Edit SA / Properties / Label Panel and "Change Super Alignment Style" Panel |
| TD-14936 | Super Alignment | "Intersection" part for super alignment |
| TD-2716 | Super Alignment | Additional fixed arc parts |
| TD-17865 | Super Alignment | Computator Kret/Culdesac Create: Right Side Drive Option |
| TD-17865 | Super Alignment | Computator Kret/Culdesac Create: Right Side Drive Option |
| TD-13555 | Super Alignment | Copy SA vertical segments computator |
| TD-18222 | Super Alignment | Equality Chainage: Add to Horizontal and Vertical Segment tables and SA tables |
| TD-4796 | Super Alignment | Extend vertical computator point/grade to horizontal named parts |
| TD-1508 | Super Alignment | Floating Arc From End |
| TD-3580 | Super Alignment | Highlight Dropped Point Locations for SA |
| TD-14109 | Super Alignment | Horizontal offset for Tin drape computator |
| TD-18196 | Super Alignment | Horizontal segments panel: add raw and equality chainages |
| TD-3958 | Super Alignment | Make "Sameas" works for SA vertical geometry |
| TD-3457 | Super Alignment | SA > Comp > Fx Arc > Centre, Radius |
| TD-18228 | Super Alignment | SA Editor: add raw and equality chainage to Horizontal Segments table |
| TD-17018 | Super Alignment | SA Editor: String attributes |
| TD-14924 | Super Alignment | SA ref table created with soft reference on |
| TD-17500 | Super Alignment | SA with Chainage Equality – CAD Table and Report |
| TD-17026 | Super Alignment | SA: new Options option |
| TD-17499 | Super Alignment | Section View SA annotation additions |
| TD-6260 | Super Alignment | Start and End Extensions for fixed line computator by 2 points |
| TD-17712 | Super Alignment | Super Alignment Part Editor with Quick CAD Commands |
| TD-17029 | Super Alignment | Thicknesses for Super Alignment |
| TD-15587 | Super Alignment | Tick to turn run chain on and off |
| TD-5024 | Super Alignment | Vert Fx Line from two 3d pts |
| TD-21045 | Survey | "Pavement Conformance" renamed to "General Conformance" |
| TD-21960 | Survey | Ability to enter bearing corrections in radiation blocks |
| TD-17319 | Survey | Add GSB option into N value settings |
| TD-18964 | Survey | Add string number to String info table |
| TD-17770 | Survey | Allow N value box to have a "None" choice. |
| TD-17944 | Survey | Batter Slope Conformance Report: show equality chainages |
| TD-20054 | Survey | Capitalization in some Topcon read/write panels incorrect |
| TD-18072 | Survey | Chainage Equality Report: mods |
| TD-20737 | Survey | Change "Pavement Conformance" to "General Conformance" |
| TD-20731 | Survey | Change panel name of Measure Projection plane bearing and ellipsoid dist |
| TD-18965 | Survey | Check Breaklines – don’t create blank models |
| TD-18966 | Survey | Check Breaklines: report when nothing found |
| TD-18967 | Survey | Check Strings: report when nothing found |
| TD-18968 | Survey | Combine both SDR reports into one |
| TD-16042 | Survey | Flat field file to tree field file with option to control opcodes as children |
| TD-17133 | Survey | GDA2020 for Point scale factor and Measure Bearing Distance |
| TD-16306 | Survey | Geodetic Reporting with Global XYZ |
| TD-19896 | Survey | Height adjustment Panel: option to use Geotiff file |
| TD-17197 | Survey | Height Adjustment: add gsb file of N-values |
| TD-17194 | Survey | Height Adjustment: tick to do reverse of Adjust method |
| TD-18969 | Survey | If no string number don't show the brackets |
| TD-22188 | Survey | New Instrument type – x,y,z,id,code,attributes |
| TD-20663 | Survey | NZ Grid Azimuth added to Projection Bearing/Distance Measure panel |
| TD-17945 | Survey | Pavement Conformance Report: show equality chainages |
| TD-20329 | Survey | Projection editor: auto fill compound projection using epsg code |
| TD-18836 | Survey | Projection: add Lambert Conformal conic option |
| TD-17414 | Survey | Projection: Survey Data Reduction Function - new Projection Box |
| TD-17050 | Survey | Projections: ISO code fields |
| TD-16824 | Survey | Remove String added to Survey Edit Strings |
| TD-19782 | Survey | Run SDR Flat to Tree when creating a new function using FLD files |
| TD-21166 | Survey | Save and reuse resection co-ords |
| TD-18972 | Survey | SDR - Radiation line when editing |
| TD-16283 | Survey | SDR Editor for 12dfield file now shows comments at the end of the line |
| TD-16820 | Survey | SDR Editor now allows Find and Find_Replace panels to remain active |
| TD-14876 | Survey | SDR editor now displays string name and heights of selected measurement |
| TD-21841 | Survey | SDR Editor tick to skip processing all SDR Attributes |
| TD-14996 | Survey | SDR Editor with more cases where coordinates are highlighted |
| TD-18971 | Survey | SDR Field editor - Pause and recalc option |
| TD-16438 | Survey | SDR Flat to Tree should not move Target Heights |
| TD-18198 | Survey | SDR Midpoint Opcodes do not display any errors in log lines |
| TD-14774 | Survey | SDR Opcodes for Offsetting Measurements on SDR Edit menus |
| TD-21861 | Survey | SDR XSLT now handles Multicodes and has improved Attribute Reporting |
| TD-17893 | Survey | Survey Data Reduction: Display Resection and Helmert prompts like Backsights |
| TD-21563 | Survey | Traverse spreadsheet drawing speed ups |
| TD-17508 | Survey | Traverse spreadsheet: new observation type measure-calculated |
| TD-20210 | Survey | TSS add bearing text to segment attributes on import |
| TD-20386 | Survey | TSS Additional survey mark conditions |
| TD-20209 | Survey | TSS always show bearing correction column |
| TD-17255 | Survey | TSS Bearing correction for individual observations |
| TD-20277 | Survey | TSS survey class doesn't update in Point Info panel |
| TD-20419 | Trimesh | "Create Trimesh Face Normals" now handle polymeshes |
| TD-21714 | Trimesh | "Trimesh from Vertical Data" panel |
| TD-21720 | Trimesh | Add a chainage interval in converting curve water pipe to trimesh |
| TD-19800 | Trimesh | Additional warning for trimesh without volumes in Trimesh Volume Report panel |
| TD-18327 | Trimesh | Attributes for model name, element name for the trimesh generated from 12D object |
| TD-15044 | Trimesh | Colour and top, bottom and side of trimeshes |
| TD-14926 | Trimesh | Colour trimesh aspect from a range file |
| TD-14914 | Trimesh | Colour trimesh sides (top, bottom and edge) |
| TD-14927 | Trimesh | Colour trimesh slope from a range file |
| TD-16414 | Trimesh | Create a trimesh face from picking 3 vertices |
| TD-11207 | Trimesh | Create Trimesh from scratch |
| TD-18879 | Trimesh | Create trimesh pavements from tins |
| TD-17548 | Trimesh | Cut and Fill: attributes for cut and fill objects recording top and bottom tins |
| TD-20926 | Trimesh | Deprecate "Convert Faces to Trimesh" |
| TD-17941 | Trimesh | Draw polygons of a polymesh |
| TD-20422 | Trimesh | Explode Trimesh: allow for planar and non planar faces |
| TD-20150 | Trimesh | Flip one face of a trimesh |
| TD-20180 | Trimesh | Polymesh picking and highlighting |
| TD-20421 | Trimesh | Polymesh: an option to get the boundaries of non-triangle faces |
| TD-20810 | Trimesh | Repair non manifold edges by removing faces |
| TD-14767 | Trimesh | Report trimesh top surface area |
| TD-20983 | Trimesh | Skip non-planar polygons in Trimesh from 3D Planar Polygons |
| TD-16628 | Trimesh | Split a trimesh face by selecting a point |
| TD-17935 | Trimesh | Tick box on "Trimesh from 3d planar polygons" to create polymesh |
| TD-17019 | Trimesh | Trimesh Editor: Trimesh attributes |
| TD-20927 | Trimesh | Trimesh from 3D Planar Polygon: Create log lines for invalid planar polygons |
| TD-14867 | Trimesh | Trimesh healing |
| TD-17177 | Trimesh | Trimesh panels to use full data source |
| TD-18891 | Trimesh | Trimesh Union: Clean model tick box |
| TD-17743 | Trimesh | Trimesh: Polyfaces - a collection of adjacent triangles |
| TD-14899 | Views | Add Tin Settings to Perspective View Properties |
| TD-17771 | Views | E snap to pick on the surfaces of a Super String |
| TD-20445 | Views | New Views created as non threaded |
| TD-20745 | Views | Non openGL Plan views can only show polymesh |
| TD-19831 | Views | Perspective OpenGL View: Allow XYZ stick diagram at all times and to be toggled on/off |
| TD-19830 | Views | Perspective OpenGL View: colours and Text for XYZ stick diagram |
| TD-17721 | Views | Perspective OpenGL View: Default Shade angle to be 35 degrees. |
| TD-19868 | Views | Super String Box Pipe wireframes plus solid drawing |
| TD-19872 | Views | Super String multi extrusions wireframes plus solid drawing |
| TD-19869 | Views | Super String Round Pipe wireframes plus solid drawing |
| TD-19871 | Views | Super String with circle and arcs in extrusion wireframes plus solid drawing |
| TD-19870 | Views | Super String with polygon extrusion wireframes plus solid drawing |
| TD-20444 | Views | The default draw colour for edges is now RGB(128,128,128) |
| TD-15095 | Views | Tin Height Render Settings without any module |
| TD-19873 | Views | Tins and Super Tins wireframes plus solid drawing |
| TD-19875 | Views | Water String Nodes wireframes plus solid drawing |
| TD-19874 | Views | Water Strings Links wireframes plus solid drawing |
| TD-19927 | Visualisation | glelibrary draw wireframes with custom edges |
| TD-20094 | Visualisation | New option to remove duplicate identical extrusions |
| TD-21574 | Volumes | Add totals to Polygon Report |
| TD-16044 | Volumes | Cut and Fill trimeshes between two tins Step 1 |
| TD-17284 | Volumes | Grid Cell Volumes: Not include empty cells, Rotate grid and Label/report on individual cells |
| TD-16178 | Widgets | Show filename of missing images for toolbars etc |